IMPROVEMENT OF MICROPROCESSOR COMPLEX SCHEME USING MICROPROCESSOR HARDWARE COMPLEX

Authors

DOI:

https://doi.org/10.15802/stp2019/196015

Keywords:

automation, overheated axlebox, heating, trackside chambers

Abstract

Purpose. During the maintenance of equipment for overheated axleboxes detecting, the problem of the time consumption for manual measurement of the trackside chambers temperature appeared. This is impractical in the era of using electronic programmable devices. The purpose of this article is to improve the heating control scheme for trackside chambers of the microprocessor hardware complex, namely the subunit of the microprocessor thermostat, which is designed to maintain a stable temperature inside the trackside chambers. Methodology. The studies are based on statistical data obtained as a result of the operation of overheated axleboxes detection equipment. In the article the methods of circuit simulation to obtain a microelectronic scheme have been applied. Findings. The work has considered the problem of manual servicing overheated axlebox detection equipment. The necessity of automation measurement procedure, processing and transmission of data on the temperature of the trackside chamber has been determined. An electronic scheme based on a microcontroller has been developed, which allows you to react in case of appearance of possible temperature changes outside the specified limits. The performed calculations show that the proposed scheme significantly reduces the time for servicing the equipment and eliminates the human factor, which can influence the reliability of the readings during the temperature measuring. Originality. For the first time, an improved scheme for controlling the heating of trackside chambers based on a microcontroller has been proposed, which allows automatical adjusting and maintains the temperature in the trackside chamber from 21 to 40°C, and gives the alarm signal when the thermistor fails and temperature fluctuates outside the set limits. Practical value. The heating control scheme applying allows automation of temperature measurements inside the trackside chamber. This significantly reduces the maintenance time for overheated axlebox detection equipment, since it completely eliminates both the necessity for manual check of the temperature with a mercury thermometer between trains traffic and the necessity for manual adjusting the temperature in case of its discrepancy to the standards.

Author Biographies

K. I. Yashchuk, Dnipro National University of Railway Transport named after Academician V. Lazaryan

Dep. «Automation and Telecommunications», Dnipro National University of Railway Transport named after Academician V. Lazaryan, Lazaryana St., 2, Dnipro, Ukraine, 49010, tel. +38 (056) 373 15 04, e-mail k.i.yaschuk@gmail.com

S. S. Petrovsky, Dnipro National University of Railway Transport named after Academician V. Lazaryan

Dep. «Automation and Telecommunications», Dnipro National University of Railway Transport named after Academician V. Lazaryan, Lazaryana St., 2, Dnipro, Ukraine, 49010, tel. + 38 (056) 373 15 04, e-mail sserghp@gmail.com

References

Maryuhnenko, V. S., Muhopad, Yu. F., Mironov, B. M., & Alekseenko, V. A. (2016). Avtomatizirovannyy kontrol podvizhnogo sostava na khodu poezda : uchebnoe posobie. Irkutsk: IrGUPS. (in Russian)

Ivanova, V. Yu. (2017). Sistemy beskontaktnogo obnaruzheniya nagretyh buks vagonov. Aktualnye napravleniya nauchnyh issledovanij: perspektivy razvitiya, 261-263. (in Russian)

Kolontayevskij, Yu. P., & Soskov, A. G. (2009). Elektronika i mikroshemotehnika: pidruchnik. Kiev: Karavela. (in Ukrainian)

Kompleks tekhnicheskikh sredstv dlya modernizatsii apparatury PONAB-3 i DISK-B «KTSM-01D». (2001). Ekspluatatsionnaya dokumentatsiya : albom 1–4. Retrieved from https://studfile.net/preview/8166000/page:2/

Matviikiv, M. D., Vus, B. S., & Matviikiv, O. M. (2015). Elementy ta komponenty elektronnykh prystroiv: pidruchnyk. Lviv: Lvivska politekhnika. (in Ukrainian)

Martynov, I. E., Nejchev, O. V., Sosunov, A. A., Petukhov, V. M., & Trufanova, A. V. (2018). Thermal checking hot box system knots of rolling stock. Informacijno-keruyuchi sistemi na zaliznichnomu transporti, 5, 32-38.

Soskov, A. G., & Kolontayevskij, Yu. P. (2017). Promislova elektronika: pidruchnik. Kiev: Karavela.

Ukazaniya o poryadke zameny, proverki i remonta v KIPe ustroystv sistemy DISK-BKV-Ts: Utv. Gl. upr. signalizatsii, svyazi i vychisl. tekhniki M-va putey soobshch. SSSR 29.06.90. Moskva: Transport. (in Russian)

Cherepov, O. V., & Kozarezova, M. A. (2017). Informatsionnye tekhnologii i sistemy kompleksnogo kontrolya tekhnicheskogo sostoyaniya vagonov. Chast 2. Sistemy kompleksnogo kontrolya tekhnicheskogo sostoyaniya vagonov: uchebnoe posobie. Ekaterinburg: UrGUPS.

Tarawneh, C., Aranda, J. A., Hernandez, V. V., & Ramirez, C. J. (2018). An Analysis of the Efficacy of Wayside Hot-Box Detector Data. Joint Rail Conference. doi:10.1115/jrc2018-6218

Asdrubali, F., Baldinelli, G., Bianchi, F., Costarelli, D., Rotili, A., Seracini, M., & Vinti, G. (2018). Detection of thermal bridges from thermographic images by means of image processing approximation algorithms. Applied Mathematics and Computation, 317, 160-171. doi: 10.1016/j.amc.2017.08.058

He, D., Xu, K., & Zhou, P. (2019). Defect detection of hot rolled steels with a new object detection framework called classification priority network. Computers & Industrial Engineering, 128, 290-297. doi:10.1016/j.cie.2018.12.043

Garip, G., Ustoglu, I., Mumcu, T. V., & Kaymakci, O. T. (2014). Hot box detection system design for railway vehicle safety. 5th International Conference on Design and Product Development, 31-36. (in English).

Toullier, T., Dumoulin, J., & Mevel, L. (2019). Study of complementary multi-sensors data influence on infrared thermography measurements for in-situ long-term monitoring. Multimodal Sensing: Technologies and Applications, 1-10. doi: 10.1117/12.2526229

Downloads

Published

2019-12-29

How to Cite

Yashchuk, K. I., & Petrovsky, S. S. (2019). IMPROVEMENT OF MICROPROCESSOR COMPLEX SCHEME USING MICROPROCESSOR HARDWARE COMPLEX. Science and Transport Progress, (6(84), 7–15. https://doi.org/10.15802/stp2019/196015

Issue

No. 6(84) (2019)

Section

AUTOMATED AND TELEMATIC SYSTEMS ON TRANSPORT

License

Copyright and Licensing

This journal provides open access to all of its content.
As such, copyright for articles published in this journal is retained by the authors, under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0). The CC BY license permits commercial and non-commercial reuse. Such access is associated with increased readership and increased citation of an author's work. For more information on this approach, see the Public Knowledge Project, the Directory of Open Access Journals, or the Budapest Open Access Initiative.

The CC BY 4.0 license allows users to copy, distribute and adapt the work in any way, provided that they properly point to the author. Therefore, the editorial board of the journal does not prevent from placing published materials in third-party repositories. In order to protect manuscripts from misappropriation by unscrupulous authors, reference should be made to the original version of the work.